Cover Plate Selection Process Details
You select the units of measurement that you prefer; inch (in) or centimeter (cm).

You accurately measure (within +-1/8" or +-0.25cm) the dimensions of the hole that you would like to cover. For a rectangular hole, you measure the width and height of the hole. For a circular hole, you measure the hole diameter.

You accurately measure the thickness (within +-1/32" or +-0.1cm) of the wall material.

You ensure that there is enough clearance "empty space" inside the hole to fit the retaining bracket which holds the cover Plate flat against the wall (4" or 10cm of clearance "empty space" is required from the edge of the hole toward the inside of the hole along the direction of the holding bracket and 2" or 5cm of clearance is required from the hole surface toward the inside of the hole along the direction perpendicular to the Cover Plate).

You select the orientation of the holding bracket. The holding bracket can be placed along (in the direction of) the Cover Plate width dimension or along (in the direction of) the Cover Plate height dimension. For improved holding force it is recommended to place the holding bracket along the longest lenght (unless there is something that might obstruct the holding bracket inside the wall in that direction).
Note : For circular Cover Plate there is no bracket direction.

You select the bracket offset. For certain specific size of square or rectancular Cover Plate, the holding bracket is placed in the middle of the Cover Plate along the direction you've specified. For improved holding force, it is recommend not to offset the holding bracket. However, when there is an obstruction located right behind the Cover Plate, offsetting the Cover Plate bracket might clear the obstacle. When offset is selected (if the bracket size and design allows it), the bracket is placed as closed to the hole edge as possible.
Warning : Depending on the nature of the obstruction, offseting the holding bracket might not clear the obstruction and allow the holding bracket to be normally inserted into the hole. Specially if the obstruction is large. The offseted bracket is intented to clear an obstruction of relatively small dimension (no bigger than 1/2 of the smallest Cover Plate hole dimension).

You optionally select a feature to be added to your Cover Plate. The feature can be one of the following : RCA (audio/video), hole, hole with groove, ethernet (RJ45), cable plug (CAOX), phone plug. When you select a feature your Cover Plate will be made specifically for the feature you've selected and the plug/coupler (ethernet coupler, cable coupler, phone outlet, RCA coupler) will be inserted on the Cover Plate. A maximum of 4 features can be added to your Cover Plate (if the Cover Plate size permits it).
Note : The hole diameter is selectable up to a maxium diameter which is function of the Cover Plate dimension. The number of RCA couplers is selectable up to a maximum of 5 RCA couplers for a feature.
Caution : The Cover Plate is not intended to be used with high voltage or high current electrical cables.

Cover Plate Production Process
Once your payment is received. The RoutCad™ software is used to custom design your Cover Plate according to your specifications. Your Cover Plate is custom made with the high fidelity CNC (Computer Numerical Control) RouBot™ software.

Cover Plate Delivery Time
Once your payment is received, you have to allow 15 business days for design, 15 business days for manufacturing, and 20 business days for delivery if the package is to be shipped within Canada or the Continental USA. If the shipping location is outside of Canada or the Continental USA, the delivery time may be longer. The shipment method is Federal Express Ground or USPS (Canada Post).
These Cover Plates are made in Canada. If you're located in Canada or the USA these Cover Plates are duty free under NAFTA. You may have to pay duty on the items if you're located outside of Canada or the USA. If Duty is applicable; it is the responsibility of the buyer. Any other custom, brokerage or related fees are the responsibility of the buyer.

Price and Taxes
Prices are subject to change without notice. The price paid do not include taxes (except for Canada resident). The buyer is responsible for remitting any applicable taxes to its local, provincial or state authorities if the item is taxable in the buyer local region, province or state. If the buyer is located in Canada, the seller will remit the applicable taxes to the Québec Government.

Errors and Bugs
The web site, installation guide, promotional brochures, business card, and any other related documentations to the Cover Plate may contains typographical errors, errors in the pictures, errors in the explanation, errors in the examples, or other errors. The RoutCad web site may also contain errors and or bugs. The above mentioned bugs and errors that may exist are not significant and do not preclude the utilization or installation of the Cover Plate. If any provisions of these "Terms and Conditions" would be deemed inadmissible by the "court of law" the balance of the "Terms and Conditions" remains in full effect.
Note : For the website to functionned normally "Cookies" and "JavaScript" must be enabled.

Limited Warranty and Responsibility
The manufacturer offers a limited time and limited scope warranty on the Cover Plate when there is no obstruction inside the wall that might prevent or limit the insertion and usage of the Cover Plate. When the above condition is met and the Cover Plate is used in accordance with the installation instruction, the manufacturer explicitly warranty for a maximum period of 3 months from the date of original purchase or a maximum of 5 installation/removal cycles, which ever comes first, that the Cover Plate will meet it intended purpose of Covering a hole of dimensions (width, height, and thickness) which the Cover Plate was originally designed for. Under these specific conditions the manufacturer will promptly replace the defective Cover Plate. The limited warranty covers for a maximum time period of three months from the date of original purchase or a maximum of 5 installation/removal cycles which ever comes first, only a design or production error commited by the manufacturer, where the produced Cover Plate would no cover the hole it was originally designed for.
Each Cover Plate is custom design and made as per the client specifications, the manufacturer is not responsible for errors in the measurement made or any other errors made by the client which may cause the Cover Plate not to meet it intended function. The manufacturer can't be held responsible for any personal injury , property damages, or loss of revenue resulting in the misuse of the Cover Plate and any of its accessories. The manufacturer declines any liabilities or responsibilities in the usage of the Cover Plate and any of its accessories.

Return Policy
All sales of Cover Plates and related accessories are final sale. Each Cover Plate is custom design and made as per the client specifications, therefore it can't be returned or exchange. Once you've submitted your order, there is no refund possible. It is highly recommended to double check your measurements before submitting your order. If unsure about a topic we encourage you to communicate with us.

LIMITATION ON AND EXCLUSION OF REMEDIES AND DAMAGES
YOU CANNOT RECOVER ANY DAMAGES, INCLUDING CONSEQUENTIAL, LOST PROFITS, SPECIAL, INDIRECT OR INCIDENTAL DAMAGES. This limitation applies to anything related to the Cover Plate and its accessories; and claims for breach of contract, breach of warranty, guarantee or condition, strict liability, negligence, or other tort to the extent permitted by applicable law. It also applies even if 6704239 Canada Ltd. knew or should have known about the possibility of the damages.

LOCATION OF LITIGATION
Any litigation against 6704239 Canada Ltd. must be brought to the Montreal’s municipal court herein referred as "court of law", located in the province of Québec, Canada.